Efficiency of 3D-printed composite resin restorations compared with subtractive materials: Evaluation of fatigue behavior, cost, and time of production.

STATEMENT OF PROBLEM: Three-dimensionally (3D)-printed composite resins have been marketed as materials for definitive restorations. However, limited information is available regarding the stability of the adhesive interface and the efficiency of 3D-printed composite resins. PURPOSE: The purpose of this in vitro study was to evaluate the integrity of the marginal adhesive interface before and after thermal and mechanical fatigue of an initial formulation of a 3D-printed composite resin and to evaluate the efficiency of this manufacturing method. MATERIAL AND METHODS: Freshly extracted molars were prepared for onlays and adhesively restored with either 3D-printed composite resin (VarseoSmile Crown Plus) (Group 3D), milled composite resin (Tetric CAD) (Group MCOMP), milled PMMA (Telio CAD) (Group PMMA), and milled lithium disilicate (IPS e.max CAD) (Group EM). Marginal analysis was performed under a scanning electron microscope before and after fatigue by thermomechanical cyclic loading, and initial and terminal percentages of continuous margin (%CM) were compared. The time required for the production of each type of restoration was recorded, and the production costs were also compared. RESULTS: Before aging, 3D, MCOMP, and EM presented comparable values of %CM (69.8%, 75.9%, and 63.1%, respectively) that were statistically significantly higher (P<.05) than those of PMMA (45.1%). After aging, 3D and EM had comparable results (44.7% and 43.7%, respectively), which were lower than those of the MCOMP group (68.5%) but higher than those of the PMMA group (20.5%). Regarding time efficiency, 3D printing took less time than MCOMP or PMMA if more than 8 restorations were fabricated. For the production costs, 3D printing was 5.5, 8.7, and 10.2 times less expensive than PMMA, MCOMP, and EM, respectively. The initial equipment cost was also lower for the additive manufacturing method. However, 3D printing did not always considerably reduce waste. CONCLUSIONS: In terms of marginal adaptation, the evaluated initial formulation of a 3D-printed composite resin behaved similarly to other well-established definitive restoration materials and better than milled PMMA, both before and after fatigue. Three-dimensionally printed resins present advantages in terms of equipment and consumable costs, even for a single restoration, but also for production time when more than 8 restorations were fabricated.

Gloss retention of direct composites and corresponding CAD/CAM composite blocks.

OBJECTIVES: To compare gloss retention of four different resin composites with their corresponding CAD/CAM composite blocks. MATERIALS AND METHODS: Four direct resin composites (Filtek Supreme XTE A2 Body (3M, USA), Tetric EvoCeram A2 (Ivoclar Vivadent, Liechtenstein), GrandioSO x-tra A2 (VOCO, Germany), G-aenial Universal A2 (GC, Japan)), and their corresponding CAD/CAM composite blocks were tested. A total of 288 samples were prepared and three different tests were performed: brushing, exposition to acidic fluoride gel and exposition to alcoholic solution. Gloss values were obtained by means of a glossmeter at T0 before aging and T60 after 1 h of aging. RESULTS: Mean gloss values ranged from 0.9 after brushing tests to 79.0 after the alcohol test witnessing a high gloss variability depending on the materials and the aging test. Statistical analysis by means of two-way repeated measures ANOVA followed by Fisher's LSD post-hoc test revealed significant differences between materials, storage media, and their interactions. CONCLUSION: Gloss retention seems to be dependent on the composite type (direct or CAD/CAM block) and composite brand and varies in respect to the type of aging. CAD/CAM materials showed a higher resistance toward alcohol exposure.

Staining susceptibility of resin composite materials.

PURPOSE: To evaluate the color stability of three resin-based materials continuously exposed to various staining agents. METHODS: 144 disc-shaped specimens were made of each of the three tested composites (Essentia, Brillant, Inspiro). Half of them were 1 mm thick, the other half 1.2 mm thick. The thicker group was then polished up to 4,000 grit and reduced to 1 mm thickness, also. All specimens, after 24-hour dry storage in an incubator, received an initial color measurement by means of a calibrated reflectance spectrophotometer (SpectroShade). Specimens were then divided into six groups (n=6) and immersed in five staining solutions or artificial saliva (control). All specimens were kept in an incubator at 37°C for 28 days. Staining solutions (red wine, curry mixed in water, curry mixed in oil, tea and coffee) were changed every 7th day to avoid bacteria or yeast contamination. After 28 days of storage, spectrophotometric measurements were repeated and L*a*b* scores once more recorded to determine the color (ΔE00) changes. RESULTS: All tested materials showed significant color changes after 28 days staining immersion. ΔE00 of polished samples varied from 1.1 (Essentia/distilled water measured over a white background as well as Essentia, Inspiro/distilled water measured over a black background) to 32.5 (Inspiro/wine measured over a white background). CLINICAL SIGNIFICANCE: Staining of restorative materials seems to be dependent on the composition of the product itself. Unpolished samples were more prone to staining than the polished ones.

Synaptic release of CCL5 storage vesicles triggers CXCR4 surface expression promoting CTL migration in response to CXCL12.

The lytic function of CTL relies on the polarized release of cytotoxic granules (CG) at the immune synapse (IS) with target cells. CTL also contain CCL5 in cytoplasmic storage vesicles (CCL5V) distinct from CG, the role of which, in regulating T cell effector functions, is not understood. Using human CD8(+) T cells specific to a lung tumor-associated Ag, we show in this article that CTL release both secretory compartments into the immune synapse with autologous tumor cells. Moreover, we demonstrate that disorganization of the T cell microtubule cytoskeleton and defects in hMunc13-4 or Rab27a abrogate CG exocytosis and synaptic secretion of the chemokine. Mechanistically, synaptic release of CCL5 cytoplasmic storage vesicles likely occurs upon their coalescence with the Rab27a-hMunc13-4 compartment and results in autocrine, CCR5-dependent induction of CXCR4 cell surface expression, thereby promoting T cell migration in response to CXCL12. We propose that CCL5 polarized delivery represents a mechanism by which CTL control immune synapse duration.

Effects of adhesive composite core systems on adaptation of adhesive post and cores under load.

OBJECTIVES: To test marginal and internal adaptation of five different adhesive composite core systems under load. METHODS: 30 human premolars were endodontically prepared and obturated with an epoxy sealer and vertically condensed gutta-percha. Thereafter the entire clinical crown was removed. The teeth were randomly assigned to five different composite core groups, all using the same fiber reinforced radicular post (DT White). Gr. 1: Optibond solo plus/Nexus II/Prodigy; Gr. 2: Scotchbond 1/Rely X Arc/Filtek P60; Gr. 3: EBS multi/Compolute applicap/Pertac II; Gr. 4: ART Bond/Parapost cement/Synergy; Gr. 5: Superbond C&B catalyst S+polymer/Metafil CX. Polyvinyl-siloxane impressions of the external margins of the cores were readied before and after 1,200,000 cycles of mechanical loading with max. 100 N at 45 degrees to the longitudinal axis of the tooth. After loading, 5 of the 6 samples of each group were cut longitudinally and the sixth sample was cut transversally to be able to take replicas for evaluation of internal adaptation after loading. RESULTS: Percentages of external "continuous margins" ranged from 97.9+-4.6 to 66.5+-7.8 before and from 87.4+-25.0 to 5.8+-12.5 after loading. Internal adaptation ranged from 96.4+-8.0 to 17.1+-20.4 after loading for the core adaptation and from 89.8+-12.2 to 65.9+-14.3 for the dentin-luting composite interface and from 99.4+-1.2 to 88.6+-9.4 for the composite-post interface. CONCLUSIONS: Surprisingly, the best materials' combination for the adhesive composite core was a self-etch light cured adhesive with a chemically cured luting agent.

Biomechanical considerations for the restoration of endodontically treated teeth: a systematic review of the literature, Part II (Evaluation of fatigue behavior, interfaces, and in vivo studies).

OBJECTIVE: The restoration of endodontically treated teeth has long been guided by empirical rather than biomechanical concepts. Part I of this literature review presented up-to-date knowledge about changes in tissue structure and properties following endodontic therapy, as well as the behavior of restored teeth in monotonic mechanical tests or finite element analysis. The aim of the second part is to review current knowledge about the various interfaces of restored, nonvital teeth and their behavior in fatigue and clinical studies. REVIEW METHOD: The basic search process included a systematic review of articles contained in the PubMed/Medline database, dating between 1990 and 2005, using single or combined key words to obtain the most comprehensive list of references; a perusal of the references of the references completed the review. RELEVANT INFORMATION AND CONCLUSIONS: Nonvital teeth restored with composite resin or composite resin combined with fiber posts resisted fatigue tests and currently represent the best treatment option. In comparison to rigid metal and/or ceramic posts, when composite resin or composite resin/fiber posts fail, the occurrence of interfacial defects or severe tooth breakdown is less likely. Adhesion into the root, however, remains a challenge because of the unfavorable ovoid canal configuration, as well as critical dentin microstructure in the deepest parts of the canal. Thus, specific combinations of adhesives and cements are recommended. The clinical performance of post-and-core restorations proved satisfactory overall, in particular with a contemporary restorative approach using composite resin and fiber posts. However, the clinical literature does not clearly isolate or identify exact parameters critical to success. This, in turn, emphasizes the importance and relevance of in vitro studies to further improve the quality and long-term stability of prosthetic foundations.

Biomechanical considerations for the restoration of endodontically treated teeth: a systematic review of the literature--Part 1. Composition and micro- and macrostructure alterations.

The specific biomechanical alterations related to vitality loss or endodontic procedures are confusing issues for the practitioner and have been controversially approached from a clinical standpoint. The aim of part 1 of this literature review is to present an overview of the current knowledge about composition changes, structural alterations, and status following endodontic therapy and restorative procedures. The basic search process included a systematic review of the PubMed/Medline database between 1990 and 2005, using single or combined key words to obtain the most comprehensive list of references; a perusal of the references of the relevant sources completed the review. Only negligible alterations in tissue moisture and composition attributable to vitality loss or endodontic therapy were reported. Loss of vitality followed by proper endodontic therapy proved to affect tooth biomechanical behavior only to a limited extent. Conversely, tooth strength is reduced in proportion to coronal tissue loss, due to either caries lesion or restorative procedures. Therefore, the best current approach for restoring endodontically treated teeth seems to (1) minimize tissue sacrifice, especially in the cervical area so that a ferrule effect can be created, (2) use adhesive procedures at both radicular and coronal levels to strengthen remaining tooth structure and optimize restoration stability and retention, and (3) use post and core materials with physical properties close to those of natural dentin, because of the limitations of current adhesive procedures.

Marginal adaptation, retention and fracture resistance of adhesive composite restorations on devital teeth with and without posts.

This in vitro study generated data on the quality of marginal adaptation, fracture resistance and retention of several indirect adhesive composite configurations on root-treated premolars before and after a long-term fatigue test and compared these results to a control group of adhesive onlays on "vital" teeth. Six root-treated extracted human premolars per group, with four different restorative configurations with and without adhesive fiber posts, were evaluated. Another group of six premolars, "revitalized" by using diluted horse serum to simulate pulpal fluid and restored with adhesive composite onlays, served as the control. Marginal adaptation before and after long-term occlusal loading (1,200,000 occlusal loading cycles at max 49 N) was assessed by using the replica technique and quantitative evaluation in SEM at 200x magnification. The number of lost restorations was recorded after loading. Fracture resistance and fracture patterns were evaluated by using a universal-testing machine on the fatigued samples. No significant differences (p > 0.05) between groups were detected before and after loading for the percentage of "continuous margin" at the total marginal length. Loading had a significant (p < 0.05) effect on the percentage of "continuous margin" for the total marginal length of two groups only. No significant difference (p > 0.05) for fracture resistance was detected and no lost restorations were observed. The results suggest that for both the less decayed and the more significantly decayed devital teeth, the minimally invasive adhesive restorative approach is promising.